Forum

Edge lines in 3DPDF

Posted by John Cates on December 19, 2016 at 4:39pm in SpaceDesign 3D PDF

I am using SketchUp 2017 on a Windows 10 PC with the newest version of 3DPDF.  When I create a 3D PDF, the PDF has two buttons at the bottom of the page - one says "Show Image" and the other says "Show 3D Model".  These buttons are new to me.  If I select Show Image, the edge lines appear on the model but it is a still shot.  If I select Show 3D Model, the edge lines disappear.  When creating the PDF, I have "ALL" Edge Lines selected and have tried various widths.  The SketchUp file is 87 mgb in size.  Do you know what is going wrong?  Thanks, John

You need to be a member of Render Plus Software to add comments!

Join Render Plus Software

Email me when people reply –
Follow

Replies

  • Rich Hart December 20, 2016 at 4:36am

    There is a size limit that we run into. I's not any kind of number we can check, we just get an error back if the routine that we call that "compiles" the geometry runs out of memory.


    John Cates said:

    Hi Rich - I started eliminating some of the more complex entities in my model like roof tile details and finally got it to export to a useable 3D PDF with edges.  Maybe the models are just too big or complicated... Thank you for your help, John

  • John Cates December 20, 2016 at 4:33am

    Hi Rich - I started eliminating some of the more complex entities in my model like roof tile details and finally got it to export to a useable 3D PDF with edges.  Maybe the models are just too big or complicated... Thank you for your help, John

  • Rich Hart December 20, 2016 at 3:51am

    i looked at this again, and see that edge lines are working for me using the new extractor, but a few are missing:

    2506676523?profile=RESIZE_1024x1024

    I'll fix that and post a new version.

    Could you make a small model where they are not working for you and let me use that for testing?

  • John Cates December 20, 2016 at 2:59am

    Hi Rich, The attached file shows what happens with "Orphans only" selected.   So, If I have "All Edge Lines" selected, and don't have "Use legacy..." selected, the PDF works but has no edge lines.   If I change to "Use Legacy...", then I get the error message and no PDF is created.   Regarding memory, this PC has 16 GB of RAM - does that matter?

    Orphans Only.JPG

  • Rich Hart December 19, 2016 at 5:51pm

    Looks like it's running out of memory.

    Does it work without any edge lines? Or with just "Orphans Only"?

  • John Cates December 19, 2016 at 5:22pm

    Hi Rich,

    I tried that checkbox and get this message (attached).  It fails to create the PDF.

    Error message.JPG

  • Rich Hart December 19, 2016 at 5:07pm

    Aha! Also check this box:

    2506670520?profile=original

    Edge lines don't appear to be working in the new data extractor logic we are using now. This will go back to the old extraction method. That may be a little slower, but the edge lines should work OK.

  • Rich Hart December 19, 2016 at 5:02pm

    What version of 3D PDF are you running?

    Make sure it's the latest one posted: PL06.

    http://www.renderplus.com/wp2/download/

  • Rich Hart December 19, 2016 at 4:59pm

    To not see those "Show Image" and "Show 3D Model" buttons, check this box:

    2506671220?profile=original

    Those button just toggle between the original SketchUp image and the 3D model.

    I'm not sure why you're not seeing any edge lines. I get them in a model I just tested here.

    Maybe make a small model and send it to use to try here.

This reply was deleted.