What is the best way to set the initial view of the 3D PDF? Prior to exporting the view from sketchup I have made sure the entire model is shown. After exporting the initial 3D PDF view is zoomed way in. I tired creating scenes, but they do not se
Read more…Dear Al and Rich,
The Pounds (£) currency symbol is not visible in a PDF.
Regards
Gregory
Hello,
First, please excuse the forum photo - I don't have a picture of myself on my computer (it's a work machine) and I didn't seem to be able to join the forum without one.
I am working on a project to provide 3D data to Field Engineers embedded
Read more…Hello.
I get the message (out of memory) when I try too create the 3DPDF.
What is the problem?
Best regards.
Read more…when creating my 3dpdf file, receiving an adobe acrobat 3d parsing error. I click OK, seems to work, just wondering what it might be.
Read more…Read more…PS. Is it any chance to improve the RTF to PDF converter? The PDF files are in a region of 100 to 175MB each time.
To drop the size to 300KB I have to re-print the SpaceDesign's PDF Report using PDF Printer
Dear Al and Rich,
Any chance to add 'Save SDS' and 'Load SDS' or 'Open SDS' above the icons.
Regards
Gregory
Dear Al and Rich,
I have some problem with the new installation - my old models and assigned attributes are getting ERROR
Any new model seems to be OK.
Regards
Gregory.
I Have migrated the views from SketchUp into RPS 3D PDF. I am working at the urban scale, approximately 4 blocks by 6 blocks in size.
Can the transitions between views be adjusted?
The "whipping" around from view-to-view especially when new view is t
Read more…Can the navigation tools be fine-tuned so as not to be so sensitive and move such great distances? Is there an adjustment for this?
Converting SketchUp to RPS 3D PDF
Read more…Al Hart said:
Specifying Faces to use for areasUse Layer Name
Place the face in a special layer:
- If you place a face in the layer _SP_AREA within a component or group, it will use that face (including scaling) to determine the area of the Compon
Just installed free version, very nice! A few questions
1. How can I change the output file address inside the exporter?
2. Can I get a full page image with no margins?
3. Turned edge lines on, set very thin. Looks great, but whenever I rotate, enti
Read more…Dear Al and Rich,
The Report Layout has some problem to reflect correctly your settings. The preview is different from the PDF.
PDF Attached.
Regards
Gregory
Dear Al and Rich,
I'm testing the new version of SD LF12.
The 'Text Substitutions' option plus the 'Rich Text Editor' and 'Dynamic View of the Page Layout' with margins and image is great!
I like the option where you can input the PDF page size 'free
Read more…Dear Al,
Below is my list of small improvements / suggestions to the Space Design Report sheet.
1. Page size based on 'Default Printer' paper sizes (A2, A1, A0) etc.
2. Heading 'Font' could have Align LEFT/RIGHT/CENTER
3. 'Introduction Comments' could ha
Dear Al and Rich,
Any chance to fix the Pounds currency symbol to £ rather than the Ł.
Regards
Gregory
From a user:
I am not able to increase or decrease the width of columns in SpaceDesign LF29sd.
It is working for me, but it may be working differently that it was before.
The column width is set in 72 points per inch.
We don't apply the width if
Dear Al,
I would like to ask you if you are able to extract from SU (using SD) information about Area of Materials/Colours/Textures used for example:
- the area of different finishes as below.
Regards
Gregory
Read more…Dear Al,
Are you able to include the Component's Thumbnail in the Space Design report?
I'm asking because it is difficult for any user to imagine how much information can be extracted from the SU 'environment'. It seems like you can access to quite a
Read more…